Sarovar Tube Industries supplies extruded, drawn and peeled aluminium bar in the full range of commercial and aerospace alloys. Aluminium delivers roughly one third the weight of steel with excellent machinability and natural corrosion resistance, and the alloy and temper can be selected to favour strength, formability or weldability as the application demands.
Sarovar Tube Industries manufactures, stocks and exports Aluminium Square Rods from Mumbai to customers across the Middle East, South East Asia, Europe, Africa and the Americas. Every heat is verified by in-house testing before despatch and supported by complete documentation, so the material you receive is exactly the material you specified.
The table below sets out the standard manufacturing range for Aluminium Square Rods. Sizes and finishes outside this range are produced against firm orders.
| Parameter | Details |
|---|---|
| Size Range | 4 mm x 4 mm to 200 mm x 200 mm |
| Length | Up to 6000 mm, cut lengths from 100 mm |
| Form | Square bar, flat bar, hexagonal bar, rectangular block |
| Finish | Hot rolled, cold drawn, peeled, ground, polished |
| Tolerance | h11 and closer on request, sharp or radiused corners |
| Condition | Annealed, solution treated, aged, stress relieved |
| Dimensional Standard | ASTM B221 / B348 / EN 755 as applicable |
| Straightness | Precision straightened, suitable for direct machining |
| Description | Details |
|---|---|
| Primary Standard | ASTM B221 / B211 / EN 573 / EN 755 |
| Grade Designation | Aluminium Alloy |
| Equivalent Grades | 2014, 2017, 2024, 5052, 5083, 6061-T6, 6082-T6, 6063, 7075 |
| Product Category | Aluminium - Square Rods |
| Certification | EN 10204 3.1 as standard, 3.2 with third party inspection on request |
Aluminium Square Rods are stocked and supplied in the following alloys. Each grade is supplied with an EN 10204 3.1 mill test certificate; other alloys and tempers are available on request.
| Grade | UNS No. | Temper | Key Properties & Uses |
|---|---|---|---|
| AA 2014 | UNS A92014 | T4, T6, T651 | High-strength Al-Cu alloy for aerospace fittings, heavy-duty forgings and machined structural parts. |
| AA 2017 | UNS A92017 | T4, T451 | Free-machining duralumin for screw machine parts, fasteners and general engineering components. |
| AA 2024 | UNS A92024 | T3, T351, T4 | Excellent fatigue strength for aircraft fittings, shafts, gears and hydraulic valve bodies. |
| AA 5052 | UNS A95052 | O, H32, H34 | Good corrosion resistance and weldability for marine hardware, fuel lines and pressure parts. |
| AA 5083 | UNS A95083 | O, H111, H112 | Highest strength non-heat-treatable alloy for shipbuilding, cryogenic and offshore service. |
| AA 6061-T6 | UNS A96061 | T6, T651 | The most versatile structural alloy — strong, weldable and easy to machine and anodise. |
| AA 6082-T6 | UNS A96082 | T6, T651 | High-strength structural alloy for bridges, cranes, trusses and transport frames. |
| AA 6063 | UNS A96063 | T5, T6 | Architectural alloy with a fine surface finish for frames, rails, fittings and trims. |
| AA 7075 | UNS A97075 | T6, T651, T73 | Highest strength aluminium alloy for aerospace, moulds, tooling and high-stress machined parts. |
| Section (mm) | Section (inch approx.) | Typical Finish | Standard Length (mm) |
|---|---|---|---|
| 4 x 4 - 10 x 10 | 5/32 - 3/8 | Cold drawn | 3000 / 4000 |
| 12 x 12 - 25 x 25 | 1/2 - 1 | Cold drawn / peeled | 3000 / 6000 |
| 30 x 30 - 50 x 50 | 1 1/4 - 2 | Peeled / hot rolled | 3000 / 6000 |
| 60 x 60 - 80 x 80 | 2 3/8 - 3 1/8 | Hot rolled / forged | 3000 / 6000 |
| 100 x 100 - 150 x 150 | 4 - 6 | Forged and machined | Cut to length |
| 160 x 160 - 200 x 200 | 6 1/4 - 8 | Forged and machined | Cut to length |
Rectangular and hexagonal sections supplied to the same tolerance classes. Custom sections cut from plate or forged to order.
Composition limits in weight percent as required by ASTM B221 / B211 / EN 573 / EN 755. Every heat is verified by spectrographic analysis and positive material identification.
| Element | Composition (%) |
|---|---|
| Aluminium (Al) | Balance |
| Copper (Cu) | 0.10 - 6.10 (alloy dependent) |
| Magnesium (Mg) | 0.20 - 4.90 (alloy dependent) |
| Silicon (Si) | 0.25 - 1.30 (alloy dependent) |
| Manganese (Mn) | 0.10 - 1.20 (alloy dependent) |
| Zinc (Zn) | 0.10 - 6.10 (alloy dependent) |
| Iron (Fe) | 0.50 - 0.70 max |
| Chromium (Cr) | 0.04 - 0.35 |
Minimum room temperature properties in the supplied condition. Results for the actual heat supplied are recorded on the mill test certificate.
| Property | Value |
|---|---|
| Tensile Strength | 180 - 570 MPa depending on alloy and temper |
| Yield Strength | 70 - 505 MPa depending on alloy and temper |
| Elongation | 8 - 25% |
| Hardness | 45 - 150 HB |
| Density | 2.70 g/cm3 |
| Melting Range | essentially 570 - 660 degrees C |
Material is released only after the following checks are completed and recorded:
Aluminium Square Rods is specified across the following industries and services:
All material is manufactured and tested to ASTM B221 / B211 / EN 573 / EN 755. Equivalent grades include 2014, 2017, 2024, 5052, 5083, 6061-T6, 6082-T6, 6063, 7075. The governing standard is printed on every mill test certificate.
Every consignment ships with an EN 10204 3.1 mill test certificate covering heat-wise chemical analysis and mechanical properties. Type 3.2 certification with third party inspection by TUV, SGS, BV or Lloyd's is available when specified at the enquiry stage.
Yes. Beyond the standard range shown above we manufacture to customer drawings and specifications, including special lengths, non-standard wall thickness and machined profiles. Share your drawing with the enquiry and our technical team will confirm feasibility and lead time.
Stock items are despatched within three to five working days of order confirmation. Made-to-order material typically takes four to six weeks depending on grade, size and heat treatment requirements. Export documentation and packing are handled in house.
Custom fabrication, special sizes and complete export documentation are handled in house. Send us your drawing or specification and our technical team will come back with a detailed offer, usually within one working day.